Overview
Features of a Flat Plate Collector System
- Suitable for domestic(Home)applications
- Stainless Steel Tig Welded Inner Tank
- Superior Quality PUF Insulation
- Pure Polyester Powder Coated Aluminum Outer Cladding
- BIS Marked Copper to Copper Absorber
- NALSUN-Selective Coated Copper Fins for Higher Efficiency.
- Weather Proof Collector Box
- 4mm Toughened and Tempered Glass Glazing.
- Pure Polyester powder coated stands and support
- Available in Vertical and Horizontal Models
- Indirect heating- Heat Exchanger type and Pressurized
- Application systems are also available.
Specification
Specification - Hot Water Storage Tank - FPC
| Material & Thickness | : | Stainless Steel – 304/GRP/Boiler grade steel. |
| Type | : | Cylindrical – horizontally assembled. |
| Size | : | Ø360, Length 1800. |
| Insulation | : | P U F.40-50mm. |
| Outer Cladding | : | Pre coated galvanized Steel/Aluminum. |
| Outer Finishing | : | Pure Polyester Powder Coating finish. |
| Outer Finish Color | : | Golden Yellow & Black combination. |
| Back up Heater | : | 2 KW With thermostat control 230V AC. |
| Tank Supports | : | Fabricated and powder coated M.S. Tube |
| Tank Testing | : | Factory pressure tested for normal systems is at 2 Kg/cm². |
| Normal Working pressure of the system | : | Less than 1 Kg/cm². |
| Interconnection Tank and Collector | : | EPDM Pipe |
Normal System Specification - Collector - FPC
| No. of Collectors | : | 02 No. |
|---|---|---|
| Type | : | Copper, selectively coated with “NALSUN” Black Chrome coating. |
| Size | : | 2080mm L x 1050mm W x 100mm H |
| Absorber Material | : | Copper - Copper absorber. |
| No. of Fins | : | 9 No’s per collector |
| Header Tubes | : | Copper, Ø25 mm, 22 SWG. |
| Riser Tubes | : | Copper, Ø12.5 mm, 24 SWG |
| Header Protective coating | : | Polyurethane based coating |
| Riser to Fin Joining | : | Ultra Sonic Metal welding |
| Collector Box | : | Aluminum |
| Protective coating on Collector Box | : | Pure Polyester powder coated - Golden Yellow |
| Glass retaining angle / Aluminum | : | 25mm Pure Polyester Powder coated - Black |
| Collector back sheet | : | Aluminum Screwed to the frame |
| Back, Corner Sealing | : | Non Acidic Silicon sealant through corners and screw joint |
| Top Cover/Glazing | : | Toughened glass, 4mm thick |
| Glass Beading | : | High quality EPDM Rubber - Single Piece |
| Absorber Flanges | : | 4 mm Thick Machined brass flanges, 63 mm dia, 4 bolt holes |
| Gaskets and Grommets | : | High quality EPDM special shaped full Gaskets and Grommets |
| Insulation Bottom | : | Rock wool, 50 mm 48 kg/m³ density |
| Insulation Side | : | Rock wool, 25 mm 48 Kg/m³ density |
| Reflective foil | : | Aluminum 50 microns thick for bottom and 0.45 mm for sides |
| Collector Supports | : | Fabricated and Duly powder coated Mild Steel Sections |
Support
Service
+ 91 80 43550218 | + 91 80 43550203 | + 91 80 43550266
(24/7 IVR Support)
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
